Glass adaptor - gasket with flange, D50, Silicone

The Strofix glass adaptor gasket with flange D50 silicone is a silicone sealing ring with an integrated flange, designed for use in Strofix D50 glass adaptor assemblies. It sits between the stainless-steel cover or distancer and the glass panel, with the flange inserting into the pre-drilled hole in the glass to centre the gasket and seal the hole edge. Manufactured from silicone rubber, Ø 48 mm gasket diameter, Ø 10 mm internal hole, 2 mm flat thickness.

The gasket cushions the contact between the metal adaptor components and the glass, preventing direct metal-to-glass contact that could cause stress cracks or scratches. The flange extends through the glass hole, providing a seal around the hole edge and helping to position the gasket concentrically during assembly. Silicone offers high flexibility and maintains its elastic properties across a wide temperature range, making it suitable for both indoor and outdoor installations. Two flanged gaskets are typically required per adaptor point — one on each side of the glass panel. The gasket is sold individually.

The Ø 10 mm internal hole is sized for M10 screws or studs. The gasket is sized for D50 glass adaptors (Ø 50 mm cover, Ø 48 mm gasket body).

Use cases:

• Sealing D50 glass adaptor assemblies on balustrades, partitions, and façades
• Protecting the drilled hole edge in toughened or laminated glass from metal contact
• Replacing worn or compressed flanged gaskets in existing Strofix D50 installations
• Installations where silicone is preferred over EPDM for its flexibility or chemical resistance
• Centring the adaptor assembly on the glass hole during installation

FAQ:

What is this gasket used for?

The gasket sits between the stainless-steel adaptor component (cover or distancer) and the glass panel in a Strofix D50 point fixing assembly. The flange inserts into the drilled hole in the glass, sealing the hole edge and centring the gasket. It prevents direct metal-to-glass contact, cushions clamping pressure, and provides a seal. Two flanged gaskets are typically used per fixing point — one on each side of the glass.

How does this silicone flanged gasket differ from the EPDM flanged D50 gasket?

Two differences: the material is silicone instead of EPDM, and the internal hole diameter is Ø 10 mm instead of Ø 14 mm on the EPDM flanged D50 gasket. Silicone typically offers greater flexibility and a wider operating temperature range. Verify the screw size used in the D50 adaptor assembly before choosing between the two — they are not interchangeable if the screw size differs.

What internal hole diameter does it have?

The internal hole is fixed at Ø 10 mm on this SKU, sized for M10 screws or studs. There is no selectable hole-size option.

What material is it made from?

Silicone rubber. Silicone is flexible, maintains its elastic properties over a wide temperature range, and is resistant to UV degradation and ageing.

Which Strofix glass adaptors is it compatible with?

This gasket is sized for the Strofix D50 glass adaptor range (Ø 50 mm cover, Ø 48 mm gasket body) that uses M10 screws. It is not compatible with D30, D40, or other adaptor sizes.

How often should the gasket be replaced?

Silicone gaskets maintain their sealing properties over many years under normal conditions. Replacement is recommended if the gasket shows visible compression set, tearing, or no longer provides a seal against water ingress.

About glass adaptor gaskets

A glass adaptor gasket is a rubber or silicone washer that sits between the metal adaptor body and the glass surface, preventing direct steel-to-glass contact. It cushions the clamping force, compensates for minor surface irregularities and protects the glass edge around the drilled hole from chipping or stress cracking under load.

Strofix supplies glass adaptor gaskets in six sizes — D30, D40, 40×40, D50, D60 and D70 — in two materials: EPDM rubber and silicone. Both flat gaskets and gaskets with an integrated flange are available; flanged variants provide additional coverage around the hole perimeter.

The correct gasket depends on the adaptor diameter, the required material and whether a flanged or flat profile is needed for the assembly.