Glass holder (10-30mm) with rod 20x320mm

The Strofix glass holder (10–30 mm) with rod (20 × 320 mm) is an AISI 304 stainless-steel French balcony fitting used to secure 8.00–17.52 mm glass panels to a building structure through a Ø20 mm anchor rod with 320 mm embedment depth. Available with two fixed spacer heights (10 or 30 mm), a Ø50 mm holder body, M10 thread, and satin finish.

Each glass holder clamps the glass panel within the Ø50 mm body and transfers the load through the Ø20 × 320 mm steel anchor rod into the wall or floor slab. The M10 fastener secures the glass inside the holder. The spacer height determines the offset between the building façade and the glass panel — select 10 mm for a close-to-wall installation or 30 mm where additional clearance is needed for exterior insulation or finish layers. The spacer is not adjustable after installation; choose the correct variant at order time. The 8.00–17.52 mm glass thickness range covers standard toughened glass as well as common laminated glass buildups.

The satin finish reduces visible fingerprints and micro-scratches compared to polished stainless steel, maintaining a clean appearance on exposed French balcony fittings.

Use cases:

• French balcony glass barriers on residential apartment buildings
• Juliet balcony glass guards for full-height window and door openings
• Glass infill panels for balcony door openings in new-build and renovation projects
• Floor-to-ceiling glass safety barriers in hotels and commercial buildings
• Glass balustrade panels on upper-storey façade openings
• Multi-storey residential developments requiring consistent French balcony detailing

FAQ:

What glass thickness does this holder support?

The glass holder accepts glass panels from 8.00 to 17.52 mm thick. This range covers standard single-pane toughened glass as well as common laminated glass buildups. The glass thickness is not a selectable variant — any panel within the 8.00–17.52 mm range is compatible.

Which spacer height should I choose?

This SKU offers two spacer height options: 10 mm and 30 mm. The spacer sets the distance between the mounting surface and the glass panel. Choose 10 mm for a close-to-wall installation, or 30 mm where additional clearance is needed for exterior insulation, render, or cladding layers. The spacer height is fixed after installation and must be selected at order time.

What are the anchor rod dimensions?

The anchor rod is Ø20 mm in diameter and 320 mm long. The rod is embedded into the wall or floor structure to provide structural anchorage for the glass holder.

What is the holder body diameter?

The glass holder body has a Ø50 mm circular face. This is the visible part of the fitting that contacts the glass panel surface.

What steel grade is this holder made from?

This glass holder is manufactured from AISI 304 stainless steel with a satin finish. AISI 304 is suitable for standard interior and exterior installations. For coastal, pool, or high-humidity environments where higher chloride resistance is required, check whether an AISI 316 variant is available in the Strofix French balcony range.

Can I install this glass holder myself?

Installation requires drilling into the wall or floor slab to accommodate the Ø20 × 320 mm anchor rod, which typically involves concrete, brick, or solid masonry. Correct embedment depth and alignment are critical for structural safety. Professional installation is recommended for French balcony glass barriers.

About French Balconies

A French balcony is a glass barrier fixed directly to the building façade at a full-height window or door opening, providing fall protection without a projecting balcony slab. The glass panel is held in place by stainless-steel glass holders with integrated rods that anchor into the wall, creating a flush, minimal-hardware guardrail that preserves the open view and natural light.

Strofix supplies French balcony components in two rod sizes — Ø16 × 320 mm and Ø20 × 320 mm — in AISI 304 or AISI 316 stainless steel, with glass holders covering spacer heights from 4 to 30 mm and glass thicknesses from 6 to 12 mm.Individual glass holders and a complete component set (with left, right and bracket pieces) are available.

The correct configuration depends on glass thickness, required spacer height, rod diameter and whether the project needs individual parts or a full set.